焊接操作機在焊接技術人員工作中使用比較遍及,但是在使用焊接操作機時應留意什么呢？山東數控焊接設備小編總結了一些內容點給大家作為參考信息使用，如下：

Welding operators are widely used in the work of welding technicians, but what should be paid attention to when using welding operators? Shandong NC welding equipment editor summarized some content points for reference, as follows:

焊接前工作人員要,檢查對焊接操作設備的壓力組織應靈敏,檢查焊機設備和工具是否，夾具應牢固,氣、液壓體系無泄漏,焊接電纜絕緣外套有無破損，確認正常后,方可施焊.(在設備上進行焊接前，應先把設備的接地或接零線拆掉，焊接完后再恢復。)

Before welding, the staff shall check whether the pressure organization of the welding operation equipment is sensitive, whether the welding equipment and tools are safe, whether the clamps are firm, whether the gas and hydraulic systems are free of leakage, and whether the insulating jacket of the welding cable is damaged. Welding can be carried out only after it is confirmed to be normal (Before welding on the equipment, the grounding or neutral line of the equipment shall be removed first and then restored after welding.)

進行電焊作業前，應檢查作業環境，危險有害因素和設置監護人員。當附近有其他人員和有關設施時，應采用屏護和間隔等，保證作業。需在高處焊接作業時，一定要掛好帶。

Before electric welding operation, the operating environment shall be checked, hazardous and harmful factors shall be removed, and supervisors shall be arranged. When there are other personnel and relevant facilities nearby, shielding and spacing shall be adopted to ensure the safety of operation. When welding at heights is required, safety belts must be hung.

對焊接操作機應安頓室內,并有牢靠的接地.如多臺對焊接操作機并列安裝時,間距不得少于3m.

Butt welding operators shall be installed indoors and firmly grounded. If multiple butt welding operators are installed in parallel, the spacing shall not be less than 3m

改變焊機接頭，更換焊件需要改接二次回路時，應選擇轉移工作地點、焊機檢修暫停工作或下班等，且一定要切斷電源后方可進行操作。

When the welding machine joint is changed and the secondary circuit needs to be connected when the welding parts are changed, the work place should be transferred, the welding machine maintenance should be suspended or off duty, and the power must be cut off before operation.

焊機應設置在防雨和通風良好的地方。焊接現場不準堆放易燃易爆物品。

The welding machine shall be set in a rain proof and well ventilated place. Inflammables and explosives are not allowed to be stacked on the welding site.

以上就是給大家介紹的自動焊接設備在操作前后分別需要注意的事項，大家也要記住一點，在更換焊條時，焊工應戴絕緣手套，防止出現不必要的事故。希望以上內容能幫到大家，關注我們網站http://gzfenfa66.com了解更多！

The above are the precautions for automatic welding equipment before and after operation. You should also remember that welders should wear insulating gloves when changing welding rods to prevent unnecessary accidents. I hope the above content can help you to follow our website http://gzfenfa66.com Learn more!